Sierra hi res applewin .dsk9/23/2023 Or Disk with Copy II Plus in Drive 1 and boot Within AppleWin. Load the renamed disk from foreign directory to drive 2 and ProDOS Master Disk Then start again AppleWin and start Copy II Plus or similar program. Rename the image and copy it back to working local directory. Similar prcedure may be performed with ProDOS disk or UCSD Pascal Disks.Īgain copy one disk at Windows to a ( foreign / outside ) directory. So finally you will have a bunch of 10 working disks for own use. The disks to match the names given previously while copying them at Windows. Start there Copy II plus or similar program and change the volumenames of Then, if you like to make it perfect, you might again startup AppleWin and Not allready given to a disk tzhat is allready present in the working local directory.īy reapeating you might afterwards have for example in the working local directoryĪn amount of Diskimages named from DOS3work01.dsk till up to DOS3work10.dsk. To the next higher number for volumename making sure that this name is Repeat this precedures again and again by each time renaming the disk Rename the disk in the foreign ( other outside ) directory toĭOS3work03.dsk and copy that image to the working local directory. The next steps should be performed as often as the amount of disks are disired to create:Īnd copy that image to the usual local working directory Īfter this has been completed, leave AppleWin and move that disk again to the other foreign directory. In file copy mode the files you generaly want to have on every working disk likeĪ hello program with startup routine. After performing the init copy with Copy II plus or similar program Then you may init the DOS3work01.dsk and give it while performing the init command the Start AppleWin and load to drive 1 the DOS 3.3 MasterdiskĪnd load to Drive 2 the disk named: DOS2Work01.dsk Then copy that same disk another second time to another directory ( we´ll call trhat the "foreign" directory )ĭOS3Work01.dsk and then move it back to the working local Directory. Without working with AppleWin perform at Windows:Ĭopy a diskimage with any kind of name in the working directory of where AppleWinĮxpects usually to load it´s Disks from. Is following precisely the following instructions: So the most easieat way to create a bunch of "working-disks" Trying to write a letter in the air without paper!Īt the other hand tasks happening within AppleWinĭon´t care very much about things that happen outside in Windows. If you try to init at an empty drive within AppleWin it´s like The users MUST make difference between things that happen in Windows while running AppleWin and Just to clearup here some genral information to newbies: Then Boot the DOS Master as Disk Drive 1, and use the INIT command above. Outside of AppleWin, COPY your DOS Master, or any other Disk, and Open it as Disk Drive 2. I don't think ApplWin will do that for you. Is there something I'm missing here ? I am using Applewin Version 1.24.0.0. But the problem now is, applewin pops up and says Cannot open file, unable to recognize file format? I even tried creating new images with CiderPress, making sure it's a 5 1/4 3.3 DOS with 254 Volume Header and applewin still does not recognize the file format. DO, once back in applewin, I typed INIT HELLO, S6, D2 snd it would format the image correctly. I have loaded in a DOS 3.3 System Master disk and booted it up ( In applewin ), then I clicked on DRIVE 2 and typed in the name of the disk image I wanted to create along with the file extension, example. You may also use an Apple IIGS emulator to run Apple II games - the Apple IIGS had a 95% compatibility with its 8-bits predecessor.ĪppleWin is very easy to use, the following video shows how to run the Oregon Trail, which comes with 2 disks.I seem to be having difficulties creating disk images with applewin. Linux users can use the wonderful LinApple. Mac users can choose between Virtual ][ (not free) and OpenEmulator (OpenSource). Which runs also the Apple II, II+ and IIe. One alternative for Windows is Agat Emulator, an emulator dedicated to the Agat (a Russian clone of the Apple II), The best emulator for Windows users is AppleWin, and OpenSource software which emulates the original Apple II, Apple II+, Apple IIe and some Russian clones. Thus, many emulators have been created and maintained over the years. The Apple II (sometimes written Apple ][) was a very popular machine in the 80s and the early 90s.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |